Click To Call(689) 356-0104Click To Get A Free Estimate
Cream travertine patio beside a screened lanai with potted ferns and a lake view

Protect pool deck and patio travertine from stains

Travertine Sealing in Altamonte Springs, FL

Call (689) 356-0104 for a free travertine sealing estimate at your Altamonte Springs home.

  • Brings out deeper paver color
  • Fresh joint sand helps lock pavers in place
  • Gives weeds less room to grow
  • Makes the surface easier to keep clean
  • Free estimate, no obligation

Request a Free Estimate

Free, no obligation.

Step 1 of 2

Where are your pavers?

Please choose one.

Free EstimateNo obligation
Fast ReplyWithin 1 business day, usually much sooner
Typical Local Price$1.50 to $3.00 a sq ft to clean, sand and seal
Call Now(689) 356-0104
Travertine sealing

Who seals travertine in Altamonte Springs, and how fast do they call back?

A local contractor takes travertine sealing calls from every Altamonte Springs, FL address, and you can expect a reply inside one business day, often within a few hours. The visit and the price are free, and you decide what happens next. To get on the schedule, call (689) 356-0104.

Travertine is a soft, porous stone, so a sealer for it is not the same product that goes on concrete pavers. The stone holds tan and cream tones that stain easily when left bare, and a good sealing job keeps that color looking clean around a pool or on a back patio. Tell the contractor where the stone sits and how it is used when you ask for a free quote.

Call (689) 356-0104

Travertine pool surround with a stone coping edge and a screen cage over the water
Stone sealers

Why does travertine need a different sealer than concrete pavers?

Travertine is natural stone, and that makes it thirsty. A Gainesville stone company describes it as naturally porous, which is why water, oils and grime can soak in and leave dark spots. A concrete paver is denser and takes a different product. To go over which sealer fits your stone, call (689) 356-0104.

What is a penetrating sealer?

A penetrating (or impregnating) sealer soaks below the surface and fills the pores. An Orlando stone company recommends high-grade penetrating sealers for travertine and says surface sealers are not recommended for travertine, marble or limestone. A Gainesville company agrees that coatings can peel or flake. Ask the contractor whether the product is penetrating before you ask for a free quote.

Why is a surface coating a risk on stone?

A film that sits on the surface of travertine can trap moisture and then lift in patches, which looks worse than bare stone. Florida humidity pushes that problem along, since the stone has to breathe. If a quote lists a glossy surface coat for travertine, ask why it was chosen. To compare two bids side by side, call (689) 356-0104.

What is included

What is included when travertine is sealed?

A full job has five parts: a look at the stone, a stone-safe clean, any small repairs, the sealer and a walk-through. Cleaning and drying take the most time. Ask for each part to be named in the quote when you ask for a free quote.

Look at the stone

Chips, pits, loose joints and old coatings get noted. A Gainesville stone company says chips, cracks and open pinholes can be repaired before sealing.

Stone-safe cleaning

Dirt, algae and film are lifted with products made for natural stone, not the acid cleaners used on some concrete.

Time to dry

Stone has to be fully dry before sealer goes on, and shaded travertine under a screen cage may need extra hours.

Penetrating sealer

The product soaks into the pores in even passes, and any extra is wiped away so no shiny patches are left.

Walk-through

The contractor shows you the finished area, how long to stay off it and how to check the coat later.

Is it worth sealing travertine at all?

Sealing is a choice, and the facts cut both ways. A travertine retailer says sealing travertine is optional and does not make stone stain-proof, acid-proof or maintenance-free. It also says sealing does not replace good installation, drainage and cleaning. On the plus side, a Gainesville stone company says sealing slows absorption while the stone can still breathe, and that it makes routine cleanup easier. To talk through whether your stone needs it, call (689) 356-0104.

Pale stone beside a pool in Altamonte Springs sees splashes, sunscreen, leaf tannins and sprinkler spray every week. Those are exactly the things a penetrating sealer is meant to slow down. If the stone is indoors-only or rarely used, the case is weaker. Describe how the stone is used when you ask for a free quote.

Safe cleaning

Which cleaners are safe on travertine?

Travertine is acid-sensitive, and that decides how it is cleaned. Unilock lists marble, limestone and travertine as acid-sensitive and points to a high-alkaline cleaner for them, with a test on a hidden spot first. A Gainesville stone company says to use neutral, stone-safe cleaners and to avoid acidic products such as vinegar. A contractor should be able to name the product and the pressure before the work starts. To ask that question now, call (689) 356-0104.

What does acid do to travertine?

Acid eats the surface and leaves a dull patch, which stone people call an etch. An Orlando stone company says an etch can often be rehoned with the right abrasives. A travertine retailer adds that acid can etch the stone even when it is sealed. Mention any old dull spots when you ask for a free quote.

Can travertine be pressure washed?

A travertine retailer notes that aggressive pressure can damage the stone or its joints, so a gentle method is the safer path. That is a reason to ask what pressure and what attachment the contractor plans to use. To raise that before booking, call (689) 356-0104.

Pool decks

Does sealed travertine stay safe to walk on around a screened pool?

Footing is the first worry around a pool, and the sources do not all agree. A travertine retailer says a coating can change the walking surface and warns not to assume extra sheen is suitable for a pool deck. A penetrating product soaks into the stone instead of forming a film. Ask the contractor about wet traction and see a test patch when you ask for a free quote.

What about chlorine and salt?

The same retailer notes that salt-water pool areas have different conditions than chlorine pools. Tell the contractor which kind of pool you have, since the sealer should be approved for it. A product that suits a chlorine pool is not automatic for a salt system. To raise it, call (689) 356-0104.

Should the sealer be tested first?

Yes. That same retailer says to test the selected product on representative material before full application. A small test patch in a corner shows color and finish before the rest is done. Ask for a patch when you ask for a free quote.

How often

How often should travertine be resealed in Altamonte Springs?

Plan on one to three years for stone, with the short end for busy spots. A Gainesville stone company says resealing every one to three years suits many homes, and that high-traffic areas may need it sooner. A Space Coast company lists its water-borne sealant at 12 to 18 months of protection against stains and dirt. Concrete pavers last longer, at two to four years, so do not carry that number over. To book a check, call (689) 356-0104.

What is the splash test?

The Gainesville company describes a splash test. If water darkens the stone and soaks in instead of beading, the sealer may be wearing away. It takes a minute and costs nothing. If your result looks dark, mention it when you ask for a free quote.

Where does the coat wear out first?

Steps, the lip of a pool deck and spots where chairs drag wear first. Shaded sections under a screen cage stay damp, so they invite stains and algae sooner. Point those spots out to the contractor when you call (689) 356-0104.

Local conditions

How do Altamonte Springs sprinklers and storms affect travertine?

Water is the main local factor. Watering is off limits in Seminole County between 10 a.m. and 4 p.m., and homes on reclaimed water irrigate twice a week all year, so a sealing day has to fit around those days. Sprinkler spray also carries minerals. UF/IFAS says most Florida well water is high in iron and that orange streaks on buildings often follow irrigation with it. Orange marks on pale travertine show quickly. To plan a sealing day around your zones, call (689) 356-0104.

The city sits in a humid subtropical climate, with hot, humid summers, and a screened lanai can keep stone damp for long stretches. A Central Florida sealing company says shaded patios collect more algae. Share where your sprinkler heads point when you ask for a free quote.

Pricing

What does travertine sealing cost in Altamonte Springs?

Published pricing for natural stone is higher than for concrete pavers. An Orlando paver company lists natural stone at $2.00 to $3.50 per square foot, or $1,000 to $3,500 for a typical project, against $1.50 to $3.00 for a standard clean, sand and seal on concrete or brick. A Central Florida company lists a $1,000 project minimum, so a small patio can price near that floor. For a price on your stone, ask for a free quote.

Condition moves the number. Old coatings, stains, chips and pits add prep time, and large decks often cost less per foot than small ones. No page found lists a rate for travertine in Altamonte Springs itself, so the table below applies the Orlando range to three sizes. Holding a bid already? Call (689) 356-0104 and compare it with these figures.

Stone areaTypical exampleTravertine sealing at $2.00 to $3.50
300 sq ftBack patio$600 to $1,050, or near the $1,000 project minimum
600 sq ftPool deck inside a cage$1,200 to $2,100
1,000 sq ftLarge deck and walkway$2,000 to $3,500

Figures multiply the natural stone range of $2.00 to $3.50 per square foot published by an Orlando paver company (paversealingorlandofl.com, read November 2026). The $1,000 minimum comes from Castle Clean and Seal's Central Florida cost article. Your contractor sets the actual price after seeing the stone. Repairs, stripping an old coat and honing are usually extra.

Get a Free Estimate

Contractor wiping excess penetrating sealer from a tan travertine paver with a clean cloth
Why choose us

Why hire a contractor who works in Altamonte Springs for travertine?

A contractor who works near I-4 and State Road 436 already plans around afternoon storms and sprinkler days. Stone work leaves little room for guesswork, so ask for the product name, the test patch and the price on paper. The decision stays with you. To start, call (689) 356-0104.

Contractors who work around here

A company that covers Altamonte Springs already plans for afternoon storms and sprinkler schedules. The first visit goes smoother for that.

A free look, nothing owed

The visit and the estimate cost nothing. If the number does not fit your budget, thank the contractor and move on.

Numbers you can check

Orlando-area companies post their price per square foot, and this site lays those ranges out in plain figures. If a quote lands well outside those ranges, ask why.

You decide the pace

Get the price in writing and read it twice. Read the contractor standards page for what to confirm before you sign.

Ready for a free travertine sealing estimate?

Phone or send the short form, and a local contractor responds within one business day, often much sooner.

Call (689) 356-0104

Free, no obligation

Gloved hand pressing fresh sand into a joint between two travertine pavers at a lanai edge
Photos

How does sealed stone and paver work look at Altamonte Springs homes?

Wide freshly sealed herringbone paver driveway at a split-level home under a live oak beside a travertine or stone surface at a Seminole County home
Family on lounge chairs by a sealed gray paver pool deck with a spa beside a travertine or stone surface at a Seminole County home
Sealed paver patio with wicker chairs beside a screened porch and a lake view beside a travertine or stone surface at a Seminole County home
Sealed paver walkway curving through azalea beds to a brick front entry beside a travertine or stone surface at a Seminole County home
Close view of new concrete pavers after sealing beside a travertine or stone surface at a Seminole County home
Paver driveway with one cleaned half beside a stained half beside a travertine or stone surface at a Seminole County home
Contractor rinsing a paver driveway with a pressure washer beside a travertine or stone surface at a Seminole County home
Two contractors spraying and rolling sealer on a driveway beside a travertine or stone surface at a Seminole County home
How it works

What is the travertine sealing process, step by step?

Most jobs follow the same six steps, from the first look at the stone to the final walk with you. If you are ready to set a date, call (689) 356-0104.

Steps 1 and 2: look and clean

The contractor measures the area and checks for chips, pits, loose joints and old coatings. A stone-safe cleaner then lifts dirt and algae, with a gentle rinse so the joints keep their material. To have the stone looked at, ask for a free quote.

Steps 3 and 4: repair and dry

Small chips and open pits get filled, and the joints are refilled. The stone then dries fully, which can take a day in shade. Ask how the contractor checks for moisture when you call (689) 356-0104.

Steps 5 and 6: seal and walk it with you

A penetrating sealer goes on in even passes and any excess is wiped away. The contractor then shows you the finished stone and how long to wait before furniture and feet return. To plan the day, ask for a free quote.

Questions

Frequently Asked Questions

What happens if pavers are not sealed?

Travertine is naturally porous, according to a Gainesville stone company, so water, oils and grime soak in and can leave dark spots. Left bare in Altamonte Springs, the stone also faces afternoon storms, sprinkler spray and shade that keeps it damp. Sealing slows all of that. It does not make the stone stain-proof, so spills still need a quick wipe.

What do professionals use to seal pavers?

For travertine, stone companies point to a penetrating (impregnating) sealer that soaks into the pores. An Orlando stone company says surface sealers are not recommended for travertine, marble or limestone. A Space Coast company uses a water-borne polymer sealant that it says leaves the look of the stone unchanged. Ask the contractor to name the product and say why it suits travertine.

Is it better to spray or roll paver sealer?

Unilock, a paver maker, describes a sprayer followed by a dry roller for concrete pavers. For travertine, the method matters less than the product, since a penetrating sealer goes into the stone instead of sitting on it. Ask the contractor how the sealer is applied, how excess is removed and how long to stay off the surface.

How often do you seal pavers in Florida?

For travertine, one Florida stone company puts resealing at every one to three years, with high-traffic spots sooner. A Space Coast company lists its water-borne sealant at 12 to 18 months of protection. Concrete pavers run longer, at two to four years from an Orlando paver company, so do not apply that number to stone.

Can travertine around a screened pool in Altamonte Springs be sealed?

Yes. A stone guide warns against assuming extra sheen suits a pool deck and notes that salt-water pool areas differ. Ask for a penetrating sealer, ask about wet footing, and have a small test patch done first.

How much does travertine sealing cost in Altamonte Springs?

An Orlando paver company lists natural stone at $2.00 to $3.50 per square foot, or $1,000 to $3,500 for a typical project. A 600 square foot deck would run about $1,200 to $2,100 at those rates. One Central Florida company also lists a $1,000 project minimum, so a small area may price near that floor.

Will sealer change how my travertine looks?

It depends on the product. A Space Coast company says its water-borne polymer does not change the look of the stone, while a travertine retailer says penetrating products and surface coatings change appearance differently. Ask for a test patch on a spare tile or a hidden corner before the whole area is done.

Can vinegar or pool chemicals harm sealed travertine?

Acid can, even through a sealer. A travertine retailer says acid can etch the stone even when sealed, and a Gainesville stone company lists vinegar among products to avoid. An Orlando stone company says an acid spill can leave a dull spot that can often be rehoned. Wipe spills quickly and ask which cleaners the contractor uses.

Ask what your travertine needs next

Name your street and the stone that worries you, and a contractor writes back within one business day, often much sooner.

Call (689) 356-0104

Free, no obligation